gcnas.blogg.se - Allmänt

#Va3 and dmr programming zip file#
#Va3 and dmr programming software#
#Va3 and dmr programming download#
#Va3 and dmr programming windows#

My HT will need to be programmed to use the correct RX and TX frequencies in order to work with the repeater. These repeaters are linked to a Virginia state wide talk group (3151), so the repeaters should transmit any communication given to the talk group. We’re both within line of site of our own mountain top repeaters (repeater-a, repeater-b).

I have an HT radio, and I (ham-1) need to talk to someone (ham-2) in the state of VA on another HT. Let’s start with the story of what we are trying to do, and work with what we know, then jump into the new concepts. There are a few concepts that carry over from normal analog repeater knowledge, and some things that are just foreign. If I have italicized words, I have them listed in the definitions near the bottom of the page.

I’ll try to explain some things here that I’ve learned so that maybe you don’t have to cross *your* eyes so much. So, much like that, I have a system set up with a hot-spot (not covered in this article), DMR radio, and a lot of crossed-eyes. You would finally get it, then you would have difficulty with it again, then it would be easier, but you’re still cross-eyed! You remember? It’s the ones that you had to cross your eyes in an odd way to see the image. If there’s one thing I’ve learned, it’s that it’s really frustrating and confusing in the beginning, much like those 3D prints they used to sell at the mall back in the 90s. Also Be sure to save to radio and save a backup each time in case something goes Wrong, you can reload the backup.I’ve recently bit the bullet, and decided to try out digital radio, more specifically, DMR. YouĪfter Using 'Your Radio' Some and understand how it works, You Can down load the code-plug from the Radio, and make changes to Button functions, Scanning, Zones etc. Radio by choosing 'File' > 'Save as' in the MD-380 CPS software.

Save the copy of the code-plug that you just uploaded to your.

If the radio functions with the new code-plug,

#Va3 and dmr programming software#

When the CPS software is finished uploading your code-plug, your.

Send the code-plug to your radio using the 'Program ' > 'Write.

Intro Screen (left side bottom of the screen.), Intro Screen Lineġ (Your Name), and Intro Screen Line 2 (Your Call Sign).

The necessary edits to Radio Name (I use my call), Radio ID (your

Use the "File > Open" menu to open the code-plug thatĬlick on "General Setting" on the left side of the screen.

"default" using the "File > Save As" menu.

Save a backup of the default code-plug on your computer as.

#Va3 and dmr programming download#

Download the code-plug from your radio using the "Program >.

Open the MD-380 software by the icon on your desktop or selecting.

#Va3 and dmr programming windows#

The MD 380 Uses a direct USB Cable, The USB chip is in the radio, So beware Windows will not detect a USB Device until the Radio Is Plugged in and turned on.

Circle with the "play" icon inside -> scanning.

speaker with an 'x', all system tones are muted.

Square with L or H in it -> Low or high power.

#Va3 and dmr programming zip file#

MD 380 USB Windows Driver in Separate Zip file here if needed Tytera-MD-380-USB-Driver-v3.0.1.zip If you do not have at least Version : v1.30.0 you should Download the No Other Cable will work ! If you use the wrong cable you could damage your Radio.īefore Installing the Programming Software If your Radio did not come with a USB Programming cable, Make sure you have the right cable! The Tytra/TYT MD-380 DMR Radio uses a special Direct USB Cable. Make a Backup copy of the code-plug you received or downloaded before you start, in case any thing goes wrong, you will have a good copy.ģ. Have your Radio identification number Handy that you got from DMR-MARC.Ģ. Programming The MD 380: Before you start !ġ. Tytra/TYT MD-380 DMR Radio Programming And Help Will be logged on system records, the system will know and it won't work!

Not attempt to access the network without an ID and please DO NOT MAKE UP YOUR OWN ID. Request New User DMR ID Number at DMR-MARC,

In order to program your radio, DMR-MARC will provide you with a.

Him/her, where they suggest you get a code-plug as a base to start with, This avoidsĪny compatibility problems your radio and to the network. Gear, we recommend that initially, you ask one of the repeater owners While it is within the capability of an experienced user to program their own Shop, buy DMR equipment and use it straight out of the box. The equipment has to be set up correctly using the appropriate

In order to access the network and all of its features,.

Such, differs from normal analogue equivalents in two important ways. The DMR system is based on a the commercial digital standard and as Start by speaking with your local DMR Repeaters Owners Now you've bought your radio, you'll probably need some help to go live Before you Start Programming your DMR Radio